What Size Hinge Do I Need for a 1-3/8, 1-3/4 or 2-1/4 Inch Door?
Published November 10, 2026 • 7 min read • For homeowners, carpenters, door installers and hardware specifiers
Door thickness picks the starting hinge size, and door width adjusts it. In the common industry chart (Hager Commercial Hinges Catalog, 2024), a 1-3/8″ door takes a 3-1/2″ hinge up to 32″ wide and a 4″ hinge from 32″ to 36″; a 1-3/4″ door takes 4-1/2″ up to 36″ wide, 5″ from 36″ to 48″ and 6″ beyond; and a door 2″ to 2-1/2″ thick takes a 5″ heavy-weight hinge up to 42″ wide. Most interior doors at home are 1-3/8″; most exterior and commercial doors are 1-3/4″.
Quick Facts
- 1-3/8″ door: 3-1/2″ hinge (4″ from 32″ to 36″ wide) — Waterson K51M-400
- 1-3/4″ door: 4-1/2″ hinge (5″ from 36″ to 48″ wide, 6″ beyond) — Waterson K51M-450
- 2″ to 2-1/4″ door: 5″ heavy weight — Waterson K51M-500 or K51M-500D
- 2-1/4″ and up: Waterson K51M-600 (6″)
- Width formula: 2 × (door thickness − backset) + clearance
- Fire doors: NFPA 80 (2022) §6.4.3.1 and the door’s listing decide
Why Thickness Comes First
“Size” on a hinge means its height and its open width, usually the same number. Thickness controls the width: the hinge pin has to sit far enough out from the door face for the door to swing past 90 degrees without hitting the casing or the wall.
Hager’s catalog gives the formula: hinge width = 2 × (door thickness − backset) + clearance. Backset, the strip of door edge left outside the hinge pocket, is 1/4″ on doors up to 2-1/4″ thick and 3/8″ on thicker doors. Clearance is the room the door needs past any trim; between standard widths, take the next larger one. Run the numbers:
| Door thickness | 2 × (thickness − 1/4″) | Clearance left by a 4-1/2″ wide hinge |
|---|---|---|
| 1-3/8″ | 2-1/4″ | 2-1/4″ |
| 1-3/4″ | 3″ | 1-1/2″ |
| 2-1/4″ | 4″ | 1/2″ |
A 4-1/2″ hinge is roomy on a 1-3/4″ door and tight on a 2-1/4″ door, where a 5″ hinge leaves a full inch. Every Waterson K51M size is listed against a door thickness, so the thickness is the first number we need before we can recommend a size.
The Thickness-to-Hinge Chart
| Door thickness | Door width | Industry hinge height | Waterson K51M |
|---|---|---|---|
| 1-3/8″ | up to 32″ | 3-1/2″ | K51M-400 (4″ × 4″) |
| 1-3/8″ | over 32″ to 36″ | 4″ | K51M-400 (4″ × 4″) |
| 1-3/4″ | up to 36″ | 4-1/2″ | K51M-450 (4-1/2″ × 4-1/2″) |
| 1-3/4″ | over 36″ to 48″ | 5″ | K51M-500 or K51M-500D (5″ × 5″) |
| 2″ to 2-1/4″ | up to 42″ | 5″ heavy weight | K51M-500 or K51M-500D |
| 2-1/4″ | over 42″ to 48″ | 6″ heavy weight | K51M-600 (6″ × 6″) |
Industry rows: Hager Commercial Hinges Catalog (2024), “Selecting a Hinge”. Waterson rows: K51M door thickness by size. Every published K51M set is rated for doors up to 4′ wide.
The K51M range starts at 4″, so a 1-3/8″ door on 3-1/2″ hinges moves up to the K51M-400; see the 4-inch self-closing door hinge. The K51M-500D is the heavy-duty 5″ hinge, listed for the same 1-3/4″ to 2-1/4″ doors as the K51M-500. A 2-1/4″ door sits at the top of the K51M-500 range and the start of the K51M-600 range: choose by the clearance the opening needs and the frame preparation, then check the set’s load rating. For the 6″ size, see 6-inch door hinges.
A homeowner wrote to us after noticing that the 4-1/2″ hinges on our site were listed for 1-3/4″ doors, while their own door was only 1-3/8″ thick, and asked whether we had a mechanical self-closing hinge for it. We did: the K51M-400 is the size listed for 1-3/8″ doors, and an A set is the mechanical-only version. Rebuilding a wooden screen door? See can I replace my screen door closer with self-closing hinges.
Measure the Door You Have
Before ordering, measure:
- Door thickness at the hinge edge. JELD-WEN and Therma-Tru literature lists 1-3/8″ interior and 1-3/4″ exterior doors as the usual residential thicknesses.
- The hinge already on the door: its height, and its corners. Residential hinges come with square, 1/4″ radius or 5/8″ radius corners (Ives residential hinge specifications), and a rounded pocket must be squared for a square-corner hinge.
- Door width, height and weight, which set the hinge count.
If the new hinge matches the old pocket in size and shape, the job is a swap. The K51M fits the standard ANSI mortise pocket as a direct drop-in replacement for standard butt hinges, with no additional door modification. That holds when the pocket is a standard ANSI mortise of the same size, such as a 4-1/2″ template pocket for a K51M-450; ANSI/BHMA A156.7-2022, the standard for template hinge dimensions, keeps template hinges the same from maker to maker. Our hinge replacement guide covers the swap step by step.
If the pocket is smaller, plan for carpentry. A church facilities contact sent us photos of solid corridor doors hanging on 3-1/2″ hinges and asked whether that would be a problem. On a solid 1-3/4″ door up to 36″ wide, the chart calls for 4-1/2″. Moving up means lengthening each mortise by an inch, plugging the old screw holes with glued hardwood dowels so the new screws bite, and squaring the corners: routine carpentry on a wood door and frame.
A hollow metal frame is different. ANSI/BHMA A156.115 (2016), Hardware Preparation in Steel Doors and Steel Frames, sets the preparations for 4-1/2″ and 5″ hinges, with a reinforcement behind each. A steel frame cannot be enlarged like a wood jamb: check the cutout, the reinforcement and the frame maker’s template, or order the hinge to match the prep.
Thickness Picks the Size; Height, Width and Weight Pick the Count
Thickness does not change how much the hinges carry. Waterson rates the set, not the size, and the K51M family shares one table:
| Hinges per door | Sets | Max door (H × W) | Max weight |
|---|---|---|---|
| 2 (rated on the K51M-450 only) | A2/B2 | 6′ × 4′ | 150 lbs |
| 3 | A3/B3/C3/D3 | 7′ × 4′ | 260 lbs |
| 4 | C4/D4 | 8′ × 4′ | 260 lbs |
| 4 | A4/B4 | 8′ × 4′ | 330 lbs |
Start from the fewest hinges whose row covers the door’s height, width and weight. Waterson then adds one hinge when the door weighs 90 % or more of that set’s rating, or when the door is at least 75 % as wide as it is tall, but only when a set with one more hinge is published for that model, size and letter; there is no rated 5-hinge set. A 7′ × 3′ door, 1-3/4″ thick, at 240 lbs is over 90 % of 260 lbs, so it moves from three hinges to a 4-hinge set, A4 or B4 rated to 330 lbs; the size stays K51M-450. Our two vs three hinges article walks through the count and the cost.
The letter is a separate choice about how the door closes. A sets are mechanical-only: spring power with mechanical friction for speed control. B sets are hydraulic hybrid: a hydraulic hinge adds damping for a smoother, quieter close. C adds hold-open to A, and D adds hold-open to B. If the door is fire-rated, read can a fire-rated door have a hold-open? before choosing C or D.
Fire-Rated Doors: the Label Decides
On a labeled fire door, the hinges must meet NFPA 80 (2022) §6.4.3.1: either the hinge requirements of Table 6.4.3.1 or the door and hardware manufacturers’ published listings. NFPA 80 also sets the count: under §6.4.3.1.1, at least two hinges for a door up to 60″ high; under §6.4.3.1.2, above 60″ one more for each additional 30″ or fraction thereof, or as the manufacturer’s published listing allows. Read the door’s label before changing hinge size; our NFPA 80 hinge requirements guide explains the rest.
The K51M is UL listed, ANSI/BHMA A156.17 Grade 1 (1,000,000+ cycle test), and permitted by NFPA 80 on fire door assemblies rated up to 3 hours, provided the size, count and listing match the door. It is investment-cast stainless steel.
Alternatives Considered
- Keep the 3-1/2″ hinges on a light 1-3/8″ interior door up to 32″ wide that does not need to close itself.
- A continuous hinge (ANSI/BHMA A156.26) on a steel frame whose prep you cannot match, after checking the installation method and, on a fire door, the listing.
- An overhead closer with plain butt hinges when the pockets must stay as they are. See self-closing hinge vs door closer.
Sizing a garage-to-house door? Our garage door self-closing article covers the code side. For the general sizing rules beyond thickness, see the hinge sizing guide.
Frequently Asked Questions
What size hinge do I need for a 1-3/4 inch door?
A 4-1/2″ hinge for a door up to 36″ wide, 5″ for 36″ to 48″ and 6″ beyond, in the common industry chart (Hager Commercial Hinges Catalog, 2024). In the Waterson range, the 4-1/2″ K51M-450 is the size listed for 1-3/4″ doors.
What size hinge do I need for a 1-3/8 inch door?
A 3-1/2″ hinge up to 32″ wide and a 4″ hinge from 32″ to 36″. Waterson self-closing hinges start at 4″: the K51M-400 is listed for 1-3/8″ doors.
What size hinge for a 2 inch or 2-1/4 inch thick door?
A 5″ heavy-weight hinge up to 42″ wide and 6″ heavy weight beyond. The Waterson K51M-500 and K51M-500D are listed for 1-3/4″ to 2-1/4″ doors, and the K51M-600 for 2-1/4″ and up.
Is a 4-1/2 inch hinge big enough for a 2-1/4 inch door?
Only just. Hager’s width formula, 2 × (door thickness − 1/4″ backset) + clearance, gives 4″ before clearance, so a 4-1/2″ hinge leaves 1/2″ and a 5″ hinge leaves 1″. In the Waterson range, a 2-1/4″ door takes the K51M-500, K51M-500D or K51M-600, not the K51M-450.
Can I replace 3-1/2 inch hinges with 4-1/2 inch hinges?
On a wood door and frame, yes, with carpentry: lengthen each mortise by an inch, plug the old screw holes with glued dowels and square any rounded corners. On a steel frame, check the existing prep and reinforcement first (ANSI/BHMA A156.115 (2016)).
Does a thicker door need more hinges?
Not by thickness alone. Door height, width and weight set the count. A Waterson 3-hinge set is rated to 7′ × 4′ and 260 lbs; a 4-hinge A4 or B4 set to 8′ × 4′ and 330 lbs.
What hinge size does a fire-rated door need?
What NFPA 80 (2022) §6.4.3.1 allows: the hinges in Table 6.4.3.1 or those in the door and hardware manufacturers’ published listings. Read the door label before you change hinge size.
Send us the door’s thickness, size, weight and a photo of the current hinge, and we will match the K51M size and set.
See Waterson hinge replacement- Hager Companies, Commercial Hinges Catalog (2024), General Information — Selecting a Hinge: height of hinge, width of hinge
- NFPA 80, Standard for Fire Doors and Other Opening Protectives, 2022 edition, §6.4.3.1, Table 6.4.3.1, §6.4.3.1.1–6.4.3.1.2
- ANSI/BHMA A156.7-2022, Template Hinge Dimensions
- ANSI/BHMA A156.115 (2016), Hardware Preparation in Steel Doors and Steel Frames
- ANSI/BHMA A156.17, Self Closing Hinges & Pivots — Grade 1; ANSI/BHMA A156.26, Continuous Hinges
- JELD-WEN prehung door literature; Therma-Tru technical manual (2017); Ives residential hinge specifications
- Waterson product documentation — K51M sizes and door thickness, load ratings, hinge sets, material, grade, fire listing