Shimming Fire Door Hinges — Q&A Guide
Direct answer: yes, you can shim hinges on a fire-rated door, with steel shims. NFPA 80 (2013) §6.4.3.4 permits steel shims when they are needed to meet the clearances in §6.3.1.7; cardboard, wood and plastic shims do not meet NFPA 80. Code text is quoted from the 2013 edition; check the edition your jurisdiction adopted. See the full article, the NFPA 80 fire door guide and self-closing fire door hinges.
The Rule
Q: Can you shim hinges on a fire-rated door?
Yes, with steel shims. NFPA 80 (2013) §6.4.3.4: “When required to meet the clearances stated in 6.3.1.7, the shimming of hinges using steel shims shall be permitted.” For Waterson K51M: the same rule applies; the K51M sits in the standard ANSI mortise pocket like any butt hinge.
Q: Can I use cardboard, wood or plastic shims on a fire door?
No. Shims of cardboard, wood, plastic or other materials do not meet NFPA 80 (iDigHardware, 2016). The cardboard shims packed with many butt hinges are for non-rated doors (Door Security + Safety, 2020). For Waterson K51M: on a rated opening, use steel shims behind the leaf, never the packing cardboard.
Q: Are stainless steel hinge shims allowed on a fire door?
The 2013 text says “steel shims” and names no grade; stainless steel is a steel. For Waterson K51M: the hinges themselves are investment-cast stainless steel, so stainless shims match the hinge material.
Q: Does shimming a hinge void the fire door label?
Steel shims used to reach the §6.3.1.7 clearances are permitted by §6.4.3.4; the assembly still has to meet its listing and pass inspection. Non-steel shims do not meet the permission: replace them with steel. Modifications outside the job-site preparations in §4.1.3.2 through §4.1.3.4 go to the listing laboratory through the manufacturer (§5.1.4.1). For Waterson K51M: the hinge is UL listed and permitted by NFPA 80 on fire door assemblies rated up to 3 hours.
Q: What is the maximum gap around a fire door?
NFPA 80 (2013) §6.3.1.7.1: 1/8″ ± 1/16″ at the head, jambs and meeting edges of steel doors; no more than 1/8″ on wood doors; measured from the pull face (§6.3.1.7.2). Under the door, 3/4″ maximum (§4.8.4.1), or, where the door bottom is more than 38″ above the floor, 3/8″ or as the manufacturer’s label service procedure specifies (§4.8.4.2). For Waterson K51M: these are the gaps to set before adjusting the hinges’ closing.
Doing the Work
Q: Where do I put the shim?
Gap too wide on the hinge side: behind the leaf, away from the barrel. Gap too wide on the latch side: on the barrel side of the leaf. Shims can go on the door leaf, the frame leaf or both; both moves the door further (Door Security + Safety, 2020). Thin steel strips tilt a leaf; full-leaf shims move the whole leaf. For Waterson K51M: shim behind the K51M leaf exactly as behind a plain butt hinge.
Q: Which hinge do I shim first?
For hinge bind, the Steel Door Institute starts at the top hinge and works down (“How to Shim Door Hinges”); for gaps and sag, pick the hinge from what you measured. When refastening, drive the screws opposite the shim first (Door Security + Safety, 2020). Close the door slowly and measure after every change.
Q: How do I fix a hinge-bound fire door?
A hinge-bound door resists closing and can spring back; first find where it touches. Bound against the rabbet: remove the hinges from the top down and add steel shims between the leaf and the door or frame; where one shim leaves a gap, the Steel Door Institute suggests two shims, each half the thickness. Bound against the stop: smaller shims between the hinge and the frame reinforcement, top hinge first. For Waterson K51M: a bound door fights the hinges’ closing force, so free the bind before adjusting the hinges.
Q: What screws do I use when I rehang a shimmed fire door hinge?
Steel. Mortise hinges into door reinforcements with steel machine screws (§6.4.3.2.2); into wood, plastic-covered composite and wood core doors with No. 12 × 1-1/4″ flat, threaded-to-the-head steel wood screws in 5/32″ pilot holes (§6.4.3.2.3); into frames with steel screws (§6.4.3.3) of the type the frame maker’s instructions and listings call for (§6.4.3.3.2). If a shim shortens the bite, check the frame or door maker’s screw requirements.
When Shims Are Not Enough
Q: Can shims fix a sagging fire door?
Small sag, yes. A broken hinge reinforcement or a twisted frame, not for long (Door Security + Safety, 2020). If shims cannot reach the clearances, the NFPA 80 Handbook points to the frame anchors or reinstalling the frame (iDigHardware, 2016). For Waterson K51M: also check the door is within the set’s rating: K51M 3-hinge sets up to 7′ × 4′ and 260 lbs; K51M A4 or B4 sets up to 8′ × 4′ and 330 lbs, plus one hinge when the door is at 90 % of the rating or 75 % as wide as it is tall, where a larger set is published.
Q: What does the annual inspection check that shimming affects?
Fire doors are inspected and tested at least annually; the items in NFPA 80 (2013) §5.2.3.5.2 include alignment (item 4), clearances (item 6), closing from full open (item 7) and latching (item 9). §6.4.1.4 requires closing mechanisms adjusted so the door latches on each operation. For Waterson K51M: an aligned door lets the hinge set’s closing force reach the latch.
Q: How many hinges does a fire door need?
NFPA 80 (2013) §6.4.3.1.1: two up to 60″ of height, plus one for each additional 30″ or fraction thereof. A 7′ door needs at least three. For Waterson K51M: start from the fewest hinges whose rating covers the door (3-hinge sets up to 7′ × 4′ and 260 lbs), then add one when the door weighs at least 90 % of that rating or is at least 75 % as wide as it is tall, only where a set with one more hinge is published.
Q: When should I replace the hinges instead of shimming?
When the leaves are worn, bent or loose in their knuckles. For Waterson K51M: it drops into the existing standard ANSI pocket with no additional door modification and is ANSI/BHMA A156.17 Grade 1.
Related: fire door inspection warning signs, fire-rated door hinge checklist, hinge replacement.