Can You Shim Hinges on a Fire-Rated Door?
Published November 11, 2026 • 7 min read • For door installers, facility managers, fire door inspectors and hardware specifiers
Yes, as long as the shims are steel. NFPA 80 (2013) §6.4.3.4 says that when shimming is needed to meet the clearances in §6.3.1.7, “the shimming of hinges using steel shims shall be permitted.” Cardboard, wood and plastic shims do not meet NFPA 80 (iDigHardware, 2016), so the cardboard shims packed with many butt hinges belong on non-rated doors only.
Quick Facts
- Steel shims: permitted, NFPA 80 (2013) §6.4.3.4
- Top and side gaps: 1/8″ ± 1/16″ on steel doors, 1/8″ maximum on wood doors (§6.3.1.7.1), measured from the pull face (§6.3.1.7.2)
- Under the door: 3/4″ maximum (§4.8.4.1)
- Inspection: alignment, clearances, closing and latching, §5.2.3.5.2 items (4), (6), (7) and (9)
- Waterson K51M: fits the standard ANSI mortise pocket, so the same shimming rules apply
What NFPA 80 Actually Says
Shimming appears in NFPA 80 as a permission tied to a purpose: you shim to bring the door within the clearances of §6.3.1.7.
| Where | Maximum gap (NFPA 80, 2013) | Section |
|---|---|---|
| Head, both jambs, meeting edges of a pair — steel door | 1/8″ ± 1/16″ | §6.3.1.7.1 |
| Head, both jambs, meeting edges of a pair — wood door | 1/8″ maximum | §6.3.1.7.1 |
| Under the door | 3/4″ maximum | §4.8.4.1 |
| Under the door, bottom more than 38″ above the floor | 3/8″ maximum, or as the manufacturer’s label service procedure specifies | §4.8.4.2 |
The quotes here are from the 2013 edition. Later editions keep the steel-shim permission (Door Security + Safety, 2020, via iDigHardware) and add clearance allowances for some laminate-faced and 20-minute wood doors in steel frames, so check the edition your jurisdiction adopted and the door’s label before you set a target gap. Our NFPA 80 fire door guide covers the rest of the standard.
Stainless steel is a steel. The 2013 text names the material, not a grade.
Steel shimming is a permitted installation step, not a blanket guarantee: the assembly still has to meet its listing and pass inspection. For a Waterson-equipped fire door, the K51M is UL listed and permitted by NFPA 80 on fire door assemblies rated up to 3 hours; the door and hardware listings, hinge count and installation still have to match. See self-closing fire door hinges.
Why Fire Doors Need Shimming in the First Place
A fire door is inspected for the things a misaligned door gets wrong. Under §5.2.3.5.2 the inspector verifies that the door, frame and hinges are secured and aligned (item 4), that clearances do not exceed §4.8.4 and §6.3.1.7 (item 6), that the door closes completely from full open (item 7) and that the latch secures it (item 9). One hinge sitting a few thousandths too deep can tilt the leaf enough to fail three of those at once. Our fire door inspection warning signs article shows what inspectors flag.
Installers who hang fire doors every day treat steel shims as a consumable. A door company that wrote to us this month was restocking them by the box.
NFPA 80 §6.4.1.4 also requires every closing mechanism to be adjusted to overcome the latch so the door latches on each operation. A door that rubs the frame spends that closing force on friction. With Waterson self-closing hinges, the closing force is in the hinges themselves, so a door that drags at the head robs the hinges of the force they need at the latch.
A facility contact told us about a door that latched well when the hinges were new and stopped latching reliably a few months later. Before anyone turns a hinge adjustment, check the gaps: a door that has dropped at the latch corner needs alignment first. If the gaps are right and the door still stops short, see why a closer hinge won’t close the last 20 degrees.
How to Shim a Fire Door Hinge
Read the gaps first. Close the door and look at the head and both jambs from the pull face (§6.3.1.7.2).
- Gap too wide on the hinge side: put the shim behind the leaf on the side away from the barrel.
- Gap too wide on the latch side: put the shim on the barrel side of the leaf.
- Tight at the top on the latch side with a gap at the bottom, or the reverse: the leaf has tilted. Correct one end only, at the top hinge or the bottom hinge, using the rule above for the direction that end has to move. This works when the frame is square and the hinge reinforcements are sound.
- Hinge-bound against the rabbet: a hinge-bound door resists closing and can spring back, so first find where it touches. Against the rabbet, remove the hinges from the top down and add steel shims between the leaf and the door or frame; where one shim leaves a gap, the Steel Door Institute suggests two shims, each half the thickness.
- Hinge-bound against the stop: the Steel Door Institute uses smaller shims between the hinge and the frame reinforcement, top hinge first.
For hinge bind, the Steel Door Institute starts at the top hinge and works down; for gaps and sag, pick the hinge from what you measured. A shim can go behind the door leaf, the frame leaf or both; shimming both moves the door further than shimming one (Door Security + Safety, 2020). Thin steel strips in several thicknesses tilt a leaf; full-leaf steel shims move the whole leaf out of a deep pocket. When you refasten, drive the screws opposite the shim first. After each change, close the door slowly and measure again.
Keep the fastener rules while you work. Mortise hinges go into door reinforcements with steel machine screws (§6.4.3.2.2). On wood, plastic-covered composite and wood core doors they take No. 12 × 1-1/4″ flat, threaded-to-the-head steel wood screws in 5/32″ pilot holes (§6.4.3.2.3). On the frame they take steel screws (§6.4.3.3), of the type the frame maker’s instructions and listings call for (§6.4.3.3.2). If a shim leaves a screw short of a full bite, check the frame or door maker’s screw requirements before you lengthen it.
Waterson K51M hinges are investment-cast stainless steel and drop into the standard ANSI mortise pocket with no additional door modification, so a shim behind a K51M leaf works the same way as behind a plain butt hinge.
When Shimming Is Not the Fix
Shimming cannot repair a broken hinge reinforcement or a twisted frame, at least not for long (Door Security + Safety, 2020). If steel shims cannot bring the gaps into range, the NFPA 80 Handbook points to the frame: adjust compression anchors, reposition sill anchors on slip-on drywall frames, or reinstall the frame (iDigHardware, 2016).
Check the hinges are carrying a door they are rated for. A Waterson K51M 3-hinge set is rated for doors up to 7′ × 4′ and 260 lbs; a K51M A4 or B4 4-hinge set for doors up to 8′ × 4′ and 330 lbs. A door heavier than its set’s rating is a hinge selection problem, and shims will not hold it. Waterson starts from the fewest hinges whose row covers the door’s height, width and weight, then adds one hinge when the door weighs at least 90 % of that set’s rating or is at least 75 % as wide as it is tall, only where a set with one more hinge is published. The hinge sizing guide walks through the numbers.
NFPA 80 counts hinges by height: two up to 60″, plus one for each additional 30″ or fraction thereof (§6.4.3.1.1). A 7′ door needs at least three; the Waterson rule above can call for four. A missing hinge is a §5.2.3.5.2 item (5) deficiency that no shim corrects. Our NFPA 80 hinge requirements article covers hinge type and count.
Alternatives Considered
- Cardboard or plastic shims: cardboard suits interior non-rated doors and should stay out of exterior or damp openings (Steel Door Institute); on a fire door, replace either with steel.
- Planing the side or top edge of a wood fire door: §4.1.3.2 permits undercutting a wood or composite door by up to 3/4″ on site; it does not list trimming the side or top edges. A modification outside §4.1.3.2 through §4.1.3.4 goes to the listing laboratory through the manufacturer (§5.1.4.1).
- New hinges: when the leaves are worn, swap them. A K51M drops into the existing standard pocket and is ANSI/BHMA A156.17 Grade 1. See hinge replacement.
Frequently Asked Questions
Can you shim hinges on a fire-rated door?
Yes, with steel shims. NFPA 80 (2013) §6.4.3.4: “When required to meet the clearances stated in 6.3.1.7, the shimming of hinges using steel shims shall be permitted.”
Can I use the cardboard shims that came with the hinges on a fire door?
No. Cardboard, wood and plastic shims do not meet NFPA 80; the cardboard shims packed with many butt hinges are for non-rated doors. Use steel shims on a fire door.
Are stainless steel hinge shims OK on a fire door?
The 2013 text says “steel shims” and names no grade, and stainless steel is a steel.
Does shimming a hinge void the fire door label?
Steel shims used to reach the §6.3.1.7 clearances are permitted by §6.4.3.4. The assembly still has to meet its listing and pass inspection; non-steel shims should be replaced with steel.
What is the maximum gap around a fire door?
In NFPA 80 (2013): 1/8″ ± 1/16″ at the head, jambs and meeting edges of a steel door and 1/8″ maximum on a wood door (§6.3.1.7.1), measured from the pull face (§6.3.1.7.2); 3/4″ maximum under the door (§4.8.4.1).
Where do I put the shim on a fire door hinge?
Gap too wide on the hinge side: behind the leaf, away from the barrel. Gap too wide on the latch side: on the barrel side of the leaf. Shims can go on the door leaf, the frame leaf or both.
Can shims fix a sagging fire door?
A small sag, yes, if the frame is square and the hinge reinforcements are sound. Shims will not hold a broken reinforcement or a twisted frame; those need frame work.
How do the shimming rules apply to Waterson self-closing hinges?
The same way as to a plain butt hinge: a Waterson K51M sits in the standard ANSI mortise pocket, and NFPA 80 asks for steel shims.
To size Waterson hinges for a fire door, start with its height, width, weight and rating label.
See Waterson self-closing fire door hinges- NFPA 80, Standard for Fire Doors and Other Opening Protectives, 2013 edition — §4.1.3.2–4.1.3.4, §4.8.4.1–4.8.4.2, §5.1.4.1, §5.2.3.5.2, §6.3.1.7.1–6.3.1.7.2, §6.4.1.4, §6.4.3.1.1, §6.4.3.2.2–6.4.3.2.3, §6.4.3.3–6.4.3.3.2, §6.4.3.4
- Lori Greene, “Decoded: NFPA 80 Requirements for Hinges, Pivots, and Continuous Hinges,” iDigHardware, 2016
- Laura Frye Weaver, “The Art of Shimming a Door,” Door Security + Safety, November/December 2020 (via iDigHardware)
- Steel Door Institute, “How to Shim Door Hinges” (steeldoor.org)
- ANSI/BHMA A156.17, Self Closing Hinges & Pivots — Grade 1
- Waterson product documentation — K51M fire listing, material, mortise fit, load ratings